Real-time Dust Monitor, Model FLD-1

Specifications Real-time Dust Monitor,Model FLD-1 Item code / Model 080040-63 / FLD-1 Measuring principle / Source Light scattering method / Laser diode Measuring sensitivity 1CPM=0.001mg/m3 (for the calibration particle) Measuring range 0.001 to 100.0mg/m3 (for the calibration particle) Measuring accuracy + or – 10% (for the calibration particle) Concentration conversion factor 0.10 to 99.99 (to the Gravimetric method) Real-time Dust Monitor, Suction Pump / Flow rate Diaphragm type / 1.7 Litter per minute Flow meter / Paper filter Mass-flow sensor(Conversion flow rate 20°C, 1 atmosphere) / Ø 47mm Model FLD-1 Display LCD with back light (20 digits x 4 lines) Sampling line Dehumidifying heater (10W) Analogue DC 0 to 1V, 4 to 20mA, Item: Particle concentration (instant value) Alarm Open collector output (Rated DC24V, 0.04A) Select one from (1) Particle Output Concentration Average Value, or (2) Instantaneous Value, (3) Various Errors Collection of measured & alarm data, measurement start & stop are available USB, RS-485 with specific command Log timing Periodic: 1 to 99 minutes, (Max. 9999 points) M easurement Logging Item Particle Concentration, Suction flow rate, Ambient air pressure, Heater temperature. Options: Ambient temperature, Humidity, Wind Direction, Wind velocity Log timing At the time alam occurred A larm Logging Item Power failure, BG test error, Sensitivity correction error. Pump flow rate error, Laser error, Communication error, Heating error, Cell battery alam etc. Operating ambient temperature 0 to 40 °C Option Weather meter, PM2.5 cyclone, Support fixing hardware Dimensions / Weight 400W x 200D x 860H mm (without protrusions) / Approx. 14kg Power Supply AC100~120V, 50/60Hz, 0.5A or AC200~240V, 50/60Hz, 0.3A Special Application (on request) Note: Wireless Telecommunication System is out of our space of work, and please consult with a system warehouse. Monitoring particle at a fence line of a factory….. Case with Alarm Lump Case with Stand Frame Case with Solar Panel The Lump Illuminates when FLD-1 Size of the Stand depends on the A Solar Panel works as a supple- measures set concentration level. installation place. mental power source. Monitoring concentration of particle at a construction field….. The FLD-1 Real-time Dust Monitor is a measuring instrument with an optical scattering method particle moni- tor inside the cabinet, enabling it to continuously assess particles at outdoor locations. With this instrument, it is possible to monitor the particle concentration without changing the instrument configuration at outdoor locations. In addition, various output interfaces using multiple units of the instrument make it possible to measure the particle concentration at the fence lines of premises, or at construction sites. 150800N000

Capable of Continuously Monitoring Particle Concentration Real-time Dust Monitor Sampling and Monitoring • FLD-1 is installed inside the cabinet, so as to make continuous FLD-1 Block Diagram It is equipped with Filter Collecting unit (including Holders and suction pump), and measurement with optical scattering method particle monitor. it works as a particle monitoring and at the same time it makes particle sampling. • Sampling pump and filter holder are equipped to make measure- Comparing the two measurement results, mass concentration conversion ment of particle monitor at the same time. correlation factor is analyzed, and you may set the factor into the main flame. Particle • A dehumidifier is equipped, and you can avoid an influence by mist. Monitor Inlet• Various output interfaces make it available for a particle concentra- The TSP inlet is rain resistance, and it may sample air tion measurement at fence lines of premises, or at a construction Inlet even it rains. It is so designed as to avoid foreign object site. such as bugs from entering into the main unit, and also • It has various options such as weather meter (for wind direction, allows an user to install optional PM2.5 Cyclone. wind speed, ambient temperature, and humidity) and PM2.5 cyclone (for particle sizing). Dehumidifying Heater Notes: Mist aerosol may make the reading of a light scattering The main unit FLD-1 is dedicated for monitoring particle concentration. method particle monitor higher than actual value. The The user is requested to provide a PC and wireless or other Communication system. incorporated heater works to decrease the influence. Heater (Dehumidifier) Data Logging Cabinet FLD-1 logs data such as measurement data, and imports it into PC.Output It records measurement data continuously for about 166 hours. Detect Control Alarm USA Note: Maximum number of logging data 9999 (at average set time of 1 minute). Control Filter Maximum 100 error data such as power failer are being recorded. Unit Holder RS-485 Filter Holder Various Interface Back-up Analogue, USB, RS-485 outputs are provided, so that you Appearance with Option can remotely operate main unit, and or collect logged data Application Example 1 Installation at a Factory Filter such as measurement value, error. Particle Concentration Control at a Construction Site Pump  Image in Use • Assessing and countering particle created by demolition Placing example Protection of Detector and Pump • Preventing particle from scattering to residential houses and Purge air system with filter is incorporated so that it other buildings adjacent to construction sites protects detector unit from contamination by particle. In • Monitoring particle created by heavy machine tool addition, back-up filter is equipped so that it may protect • Controlling the safety of workers when removing earth,sand, and the pump. With these mechanism so as to make long time rubble containing dioxin, asbestos, and other toxic substances, measurement time. and taking countermeasures to prevent scatter into the peripheral environment Example of Particle Notes: Concentration * This product is a measuring equipment for monitoring particle concentration. The Measurement at a user is requested to provide a PC and wireless or other communications system. Construction Site * Deploying the necessary number of units is suggested to monitor particle at multiple Main Unit [ FLD-1 ] Optional Item for *1 *2 locations. Measurement Item Code: 080040-63 Application Example 2 Weather Meter *1 Note: Item: Wind Direction, Wind Velocity, Monitoring Fence Lines of Factory Site Support fixing hardware and Ambient Temperature, Humidity, • Monitoring dust from a source  Image of Placing Sampling filters are not included Item Code: 080040-631 • Measuring the efficacy of countermeasures to improve the source as standard accessories. • Monitoring and preventing the scatter of dust into the peripheral PM2.5 Cyclone *2 environment It is a Cyclone method sizing • Managing the safety of workers by monitoring dust that contains apparatus with PM2.5 dispersing characteristics. toxic substances Item Code: 080040-632 Notes: * This product is a measuring equipment for monitoring particle concentration. The user is requested to provide a PC and wireless or other communications system. * Deploying the necessary number of units is suggested to monitor particle at multiple locations. Optional Item for Consumable Spares Correlation with the Filtration Method(PM2.5) Installation (1) Fluororesin processed Glass Fiber Filter ‘T60A20’ The FLD-1 demonstrated a high degree of correlation in 0.080 Support Fixing Hardware Item Code: 080130-60247 concurrent measurements with the filtration method It is used to fix main unit to a One set includes 50 filters with dia. 47mm (LV250R), used for component analysis. 0.060 single pipe (Φ48.6mm). Item Code: 080040-633 (2) Sampling Filter for PM2.5 mass analysis Measurement Site: Soka City, Saitama Prefecture, Japan Item Code: 080040-7002 Measurement Period: Nov. 14, 2013 to March 19, 2014. 0.040 One set includes 50 filters with dia. 47mm 0.020 (3) Filter Cartridge One set includes 2 cartridges for protecting the detector, and 0.000 pump 0.000 0.020 0.040 0.060 0.080 Item Code: 080040-634 LV-250R(mg/m3) FLD-1(mg/m3)

Capable of Continuously Monitoring Particle Concentration Real-time Dust Monitor Sampling and Monitoring • FLD-1 is installed inside the cabinet, so as to make continuous FLD-1 Block Diagram It is equipped with Filter Collecting unit (including Holders and suction pump), and measurement with optical scattering method particle monitor. it works as a particle monitoring and at the same time it makes particle sampling. • Sampling pump and filter holder are equipped to make measure- Comparing the two measurement results, mass concentration conversion ment of particle monitor at the same time. correlation factor is analyzed, and you may set the factor into the main flame. Particle • A dehumidifier is equipped, and you can avoid an influence by mist. Monitor Inlet• Various output interfaces make it available for a particle concentra- The TSP inlet is rain resistance, and it may sample air tion measurement at fence lines of premises, or at a construction Inlet even it rains. It is so designed as to avoid foreign object site. such as bugs from entering into the main unit, and also • It has various options such as weather meter (for wind direction, allows an user to install optional PM2.5 Cyclone. wind speed, ambient temperature, and humidity) and PM2.5 cyclone (for particle sizing). Dehumidifying Heater Notes: Mist aerosol may make the reading of a light scattering The main unit FLD-1 is dedicated for monitoring particle concentration. method particle monitor higher than actual value. The The user is requested to provide a PC and wireless or other Communication system. incorporated heater works to decrease the influence. Heater (Dehumidifier) Data Logging Cabinet FLD-1 logs data such as measurement data, and imports it into PC.Output It records measurement data continuously for about 166 hours. Detect Control Alarm USA Note: Maximum number of logging data 9999 (at average set time of 1 minute). Control Filter Maximum 100 error data such as power failer are being recorded. Unit Holder RS-485 Filter Holder Various Interface Back-up Analogue, USB, RS-485 outputs are provided, so that you Appearance with Option can remotely operate main unit, and or collect logged data Application Example 1 Installation at a Factory Filter such as measurement value, error. Particle Concentration Control at a Construction Site Pump  Image in Use • Assessing and countering particle created by demolition Placing example Protection of Detector and Pump • Preventing particle from scattering to residential houses and Purge air system with filter is incorporated so that it other buildings adjacent to construction sites protects detector unit from contamination by particle. In • Monitoring particle created by heavy machine tool addition, back-up filter is equipped so that it may protect • Controlling the safety of workers when removing earth,sand, and the pump. With these mechanism so as to make long time rubble containing dioxin, asbestos, and other toxic substances, measurement time. and taking countermeasures to prevent scatter into the peripheral environment Example of Particle Notes: Concentration * This product is a measuring equipment for monitoring particle concentration. The Measurement at a user is requested to provide a PC and wireless or other communications system. Construction Site * Deploying the necessary number of units is suggested to monitor particle at multiple Main Unit [ FLD-1 ] Optional Item for *1 *2 locations. Measurement Item Code: 080040-63 Application Example 2 Weather Meter *1 Note: Item: Wind Direction, Wind Velocity, Monitoring Fence Lines of Factory Site Support fixing hardware and Ambient Temperature, Humidity, • Monitoring dust from a source  Image of Placing Sampling filters are not included Item Code: 080040-631 • Measuring the efficacy of countermeasures to improve the source as standard accessories. • Monitoring and preventing the scatter of dust into the peripheral PM2.5 Cyclone *2 environment It is a Cyclone method sizing • Managing the safety of workers by monitoring dust that contains apparatus with PM2.5 dispersing characteristics. toxic substances Item Code: 080040-632 Notes: * This product is a measuring equipment for monitoring particle concentration. The user is requested to provide a PC and wireless or other communications system. * Deploying the necessary number of units is suggested to monitor particle at multiple locations. Optional Item for Consumable Spares Correlation with the Filtration Method(PM2.5) Installation (1) Fluororesin processed Glass Fiber Filter ‘T60A20’ The FLD-1 demonstrated a high degree of correlation in 0.080 Support Fixing Hardware Item Code: 080130-60247 concurrent measurements with the filtration method It is used to fix main unit to a One set includes 50 filters with dia. 47mm (LV250R), used for component analysis. 0.060 single pipe (Φ48.6mm). Item Code: 080040-633 (2) Sampling Filter for PM2.5 mass analysis Measurement Site: Soka City, Saitama Prefecture, Japan Item Code: 080040-7002 Measurement Period: Nov. 14, 2013 to March 19, 2014. 0.040 One set includes 50 filters with dia. 47mm 0.020 (3) Filter Cartridge One set includes 2 cartridges for protecting the detector, and 0.000 pump 0.000 0.020 0.040 0.060 0.080 Item Code: 080040-634 LV-250R(mg/m3) FLD-1(mg/m3)

Specifications Real-time Dust Monitor,Model FLD-1 Item code / Model 080040-63 / FLD-1 Measuring principle / Source Light scattering method / Laser diode Measuring sensitivity 1CPM=0.001mg/m3 (for the calibration particle) Measuring range 0.001 to 100.0mg/m3 (for the calibration particle) Measuring accuracy + or – 10% (for the calibration particle) Concentration conversion factor 0.10 to 99.99 (to the Gravimetric method) Real-time Dust Monitor, Suction Pump / Flow rate Diaphragm type / 1.7 Litter per minute Flow meter / Paper filter Mass-flow sensor(Conversion flow rate 20°C, 1 atmosphere) / Ø 47mm Model FLD-1 Display LCD with back light (20 digits x 4 lines) Sampling line Dehumidifying heater (10W) Analogue DC 0 to 1V, 4 to 20mA, Item: Particle concentration (instant value) Alarm Open collector output (Rated DC24V, 0.04A) Select one from (1) Particle Output Concentration Average Value, or (2) Instantaneous Value, (3) Various Errors Collection of measured & alarm data, measurement start & stop are available USB, RS-485 with specific command Log timing Periodic: 1 to 99 minutes, (Max. 9999 points) M easurement Logging Item Particle Concentration, Suction flow rate, Ambient air pressure, Heater temperature. Options: Ambient temperature, Humidity, Wind Direction, Wind velocity Log timing At the time alam occurred A larm Logging Item Power failure, BG test error, Sensitivity correction error. Pump flow rate error, Laser error, Communication error, Heating error, Cell battery alam etc. Operating ambient temperature 0 to 40 °C Option Weather meter, PM2.5 cyclone, Support fixing hardware Dimensions / Weight 400W x 200D x 860H mm (without protrusions) / Approx. 14kg Power Supply AC100~120V, 50/60Hz, 0.5A or AC200~240V, 50/60Hz, 0.3A Special Application (on request) Note: Wireless Telecommunication System is out of our space of work, and please consult with a system warehouse. Monitoring particle at a fence line of a factory….. Case with Alarm Lump Case with Stand Frame Case with Solar Panel The Lump Illuminates when FLD-1 Size of the Stand depends on the A Solar Panel works as a supple- measures set concentration level. installation place. mental power source. Monitoring concentration of particle at a construction field….. The FLD-1 Real-time Dust Monitor is a measuring instrument with an optical scattering method particle moni- tor inside the cabinet, enabling it to continuously assess particles at outdoor locations. With this instrument, it is possible to monitor the particle concentration without changing the instrument configuration at outdoor locations. In addition, various output interfaces using multiple units of the instrument make it possible to measure the particle concentration at the fence lines of premises, or at construction sites. 150800N000